Share your ENARSI v1.1 Experience

Taked exam this morning, all 49 questions are present here, exept 2 or 3, but they’re easy.
Labs are 3, all present here: IPSec Configuration SIM, VRF Configuration SIM, Redistribution & PBR SIM 2.
THANKS!!!

Is het necessary to study those questions:

OSPF & EIGRP Questions
BGP Questions
Route-map Questions
Redistribution Questions
MPLS Questions
VRF-Lite Questions
DMVPN Questions
AAA Questions
NTP Questions
Access-list Questions
Control Plane Questions
IPv6 Questions
IP SLA Questions
SNMP Questions
DHCP Questions
DNA Center Questions
Drag Drop Questions
Miscellaneous Questions

Can some please advise?

Passed my ENARSI today. There were 52 questions which includes 3 labs. Labs were VRF, Redistribution and PBR, DMPVN.

Passed my exam!!49 questions ,3labs.
DMVPN II,VRF(same as tut lab),Redistribute&PBR(slight differences of tut lab)
Almost 10 question out of tut library.
Thanks @networktut!

Please let me know. Was it necessary to configure all the answers in TUT for the IPSEC LAB on three routers? There are so many of them, so if this problem comes up, is it better not to do it due to time constraints? I am asking because there seem to be a lot of people who have already taken the exam.

@mc5963 I havent taken the test yet I am next week but there is a section that says on all 3 – Note: In this sim, the configuration must be done on all three routers R1, R2, R3. The names, attributes, key may be different so please check them carefully.

IDK if you can pass the exam without doing all 3 labs successfully.

Next week is my exam. I am very very nervous. I have all part 7 and VRF, DMVPN and redistribution labs down. What else should I focus on? Run through the rest of the parts (1-6) or keep focusing on labs?

>Not sure
thank you very much
＞Nervous
I think you are unprepared and I recommend you to reschedule the exam. This is also a problem for everyone, but since time is too short, I think you need to be able to solve each question in one minute. You don’t have much time to think about it, so you need to go through parts 1-6 and become familiar with the question patterns.

Taked exam yesterday, but i can’t find the result – only “Passed”.Аll 49 questions are present here, but 2 or 3 are slightly different. There is one that was packed with a lot of information and I missed it.
Labs are 3, all present here: IPSec Configuration SIM, VRF Configuration SIM, PBR with 10.9.99.9 and redistribution on R4. During the registration I got 140 mints but in the exam it was 120. There wasn’t enough time and that’s why I didn’t take tests only copy run start. I did all the tasks.

Thanks a lot to networktut

I passed the exam, but time was definitely not enough. When I finished my labs, there was 30 questions left with 35 minutes!!! I didn’t even read completely all of them. My labs were VRF, DMVPN_3 and SNMP_2. VRF lab took time as the screen setup, resolution of it was so bad. Most of the questions from here, but I cannot say if all since I couldn’t go through all of them as I was only able to study 10 days.

Good luck everyone and make sure to complete the labs several time to build muscle memory!

@briandy could not be more right. You need muscle memory to know the labs well enough to finish in 5 -7 mins like the instructions say. Anymore time and you have to rush through the remainder of questions. I failed but retrying again very soon – DMPVN, VRF and SNMP – didnt study snmp enough. Took too long and rushed through the rest. tut is enough

Took my second attempt last week and failed. 49 questions and 3 labs. Of the 49 questions I received 9 IPV6 questions and did not recognize 5 of them. Guess it was the luck of the draw on that one. VRF, Redistribution 1.1 (the second solution in Version 1), and IPSEC2. IPSEC 2 did not work as intended but I think they added to it on the exam. The combination of the IPV6 questions and not gaining connectivity on IPSEC2 lab I missed it. 75%, 67%, 73%, and 71%. This score also reflected what I have been testing on the practice quizzes here. Averaging about 76% but ranging from 74-85% on any of them before testing. I will attempt to get a solid 85-95% consistently and then re-test.

Passed exam yesterday , 52 question 4-5 different from here but its easy.
3 Labs (VRF , DMVPN Configuration Sim 3, Redistribution & PBR Sim with RIP )
Be careful for timing finished and remining one minute.

Thanks TUT.

Failed exam today. I completed all labs 100% with verifications and still failed. 53 questions and 3 labs. Labs were VRF (exactly as here), SNMP1(exactly as here), and DMVPN v2 with some changes. On the Spokes, the tunnel is configured as regular GRE with ‘tunnel destination 192.168.1.2’ (Hub IP). You need to remove it ‘no tunnel destination 192.168.1.2’ and do ‘tunnel mode gre multipoint’. I will study the questions again and give it another go later on. Good luck everyone!

Will my ccnp certification renew if I pass ENARSI exam. Thank you

@Anyone: for a re-certification of a valid ccnp you need 80 CISCO points. The ENARSI test gives you 40 points. So you need 40 points more. You have to do another 40 points test or prepare for ENCOR which gives you 80 points. A third possibility is to do a official CISCO learing course, also there you get points.

@t1000- Thanks for the information

Passed my exam. 52 Question, 3 Labs VRF, DMVPN (sim3), Redistribution and PBR. Labs were same as here. There are few new questions.

Needs to be careful with the time during the lab.

@Anyone CISCO U can also give you free points from time to time, of course if you pass those requirements within the free course.

Anyone here who already completed/tried the exam can verify if you can use the “TAB” to complete the command during the LAB on the actual exam? or you should hard code every command? Thank you in advance everyone.

@CCNP Wanabee – Understood. Appreciate it

＞ALS
You can still complete the rest of the command with TAB.

Hello community,

can someone explain me like i am 5y where do i get SW für labs
IOS used:
L2-ADVENTERPRISEK9-M-15.2-IRON-20151103.bin and
L3-ADVENTERPRISEK9-M-15.4-2T.bin

when i upload the labs to my EVE-ng and try to start them i am getting the error which is related to SW.

SW2: Failed to start node (12).

The other labs which i have create on my own, are having the other SW versions:
so even if i try to edit the pre-configured labs i cant link them to any sw from current
versions i use for other labs.

Thank you in Advance

>DinoBaggio
hegdepavankumar /Cisco-Images-for-GNS3-and-EVE-NG

There is a place to search using the name above.

I have download the sw images from hegdepavankumar, and upload them to eve-ng

It doesn`t matter if add the files to:
/opt/unetlab/addons/quemu ( with the correct naming for L2/L3, Qemu image .qcow2 name)
or i copy them to:
/opt/unetlab/addons/iol/bin

L2-ADVENTERPRISEK9-M-15.2-IRON-20151103.bin and
L3-ADVENTERPRISEK9-M-15.4-2T.bin

I still get the same error:

No more network devices
No bootable device.

maybe the Sw is not correct (110/150MB)?

I am planning to book the exam soon, do anyone have advice or anyone took exam to advise me??

what are the most drag and drop questions seen in the exam recently?

Passed the exam yesterday 52 questions approx 10-15 new questions but they are all answerable with you equipped with the proper experience. 3 LABS – Vrr same here, IPSEC 2 slightly different but if you deployed Ipsec before, this is easy. and last Redistribution with PBR with different requirements, but concept is same here in LAB. its kinda tricky analyze it well. Goodluck!

@ARS
Congratulations my friend,
would you pls tell in which topics are the new questions?
also what was the drag and drop question in your exam?
finally, was the time enough??

Failed today, 53 questions 3 labs(VRF, IPSEC I, SNMP II), some new questions.