Share your ENARSI Experience
February 4th, 2020
Go to comments
The new ENARSI 300-410 has come to replace the old CCNP exams so we create the “Share your ENARSI Experience” for everyone to share their experience to prepare for this new exam.
Please share with us your experience to prepare for the new ENARSI 300-410 exam, your materials, the way you learned, your recommendations… But please DO NOT share any information about the detail of the exam or your personal information, your score, exam date and location, your email…
Note: To get the new CCNP Enterprise certificate, you need to pass the ENCOR 350-401 exam (core exam) and one of the concentration exam.
Your posts are warmly welcome! Hope you will find useful information here!
Hey, valid Dumps?
is there anyone preparing to take the exam sometime this week?
Done my 968,
All questi0ns were from premium dump
ｓｉｌｇｈ．ｔｋ
A customer reports to the support desk that they cannot print from their PC to the local printer id: **. Which tool must be used to diagnose the issue using Cisco DNA Center Assurance?
A. path trace
B. ACL trace
C. device trace
D. application trace
Answer:
An engineer configured Reverse Path Forwarding on an interface and noticed that the routes are dropped when a route lookup fails on that interface for a prefix that is available in the routing table. Which interface configuration resolves the issue?
A. ip verify unicast source reachable-viarx
B. ip verify unicast source reachable-via 12-src
C. ip verify unicast source reachable-via any
D. ip verify unicast source reachable-via allow-default
@reni a customer……Answer is A
An engineer…… Answer is C
Anyone passed the exam?
Hello! Had anyone from premium membership take the exam with the 28th update?
Best Regards.
anyone took the exam ?????
Took the exam today and passed. So glad I made it this time. Almost all of the questions were from networktut. Just practice the composite quizzes including the new questions and you will be fine.
@rc congrats Thanks for sharing your experience how many questions were is the exam
Thank you @rc for sharing
anyone has appeared the exam ? please share your experience.
There were 61 questions in the exam. In my opinion some of the answers from networktut could be wrong. I was quite confident that I got almost of the answers right during the exam but just received slightly over 900 marks meaning I got some answers wrong. I practiced the composite quizzes several times including the new questions and got almost 100% every time. I am not sure which answers were wrong since CISCO wont give you breakdown of the wrong answers. I would still recommend this website since they are pretty spot on.
@RC ….. you are 100 percent correct… questions from networktut 100 percent of them were on the test but the some answers are not correct, not sure which ones for sure….be careful.
did anyone take the exam? Is there any update? please share share
@that guy, did you take the exam?
@ ensari correct , i did take it
@that guy how was the exam have you faced new questions out of networktut please share your experience
@ensari
the questions on networktut are legit, they showed up.. each one… the answers are a different story…. scored 100 on the composite tests and new questions… not going to share my score but i missed several and i know some of the responses on networktut are wrong…. id advise everyone to look into each question yourself and ensure you are choosing the right answer.
anyone took the exam today
Can you please share if premium is valid or not.
Thank you.
passed all questions were from networktut some of the answers are wrong please do check it out. the premium membership definitely worth it GOOD LUCK everyone
This is my email address (*{email not allowed}*)
dream dot 5650044 at gmail dot com
Good day, can anyone send me 300-410 dumps
Hello all…anybody take exam recently? would like to check if networktut is still valid.
Hi Guys.
Can anybody confirm the answer for this question.
Question 17
There is a picture of “Layer 2 loop symptoms” in DNAC and the config below:
interface GigabitEthernet1/0/13
switchport trunk allowed vlan 30-33
switchport mode trunk
int GigabitEthernet1/0/23
switchport trunk allowed vlan 30-33
switchport mode trunk
Refer to the exhibits. An engineer identified a Layer 2 loop using DNAC. Which command fixes the problem in the SF-D9300-1 Switch?
A. spanning-tree loopguard default
B. spanning-tree portfast bpduguard
C. spanning-tree backbonefast
D. no spanning-tree uplink fast
and for this question.
Refer to the exhibit. An IP SLA was configured on router R1 that allows the default route to be modified in the event that Fa0/0 losses reachability with the router R3 Fa0/0 interface. The route has changed to flow through route R2.
Which debug command is used to troubleshoot this issue?
IP_SLA_Debug.jpg
A. debug ip flow
B. debug ip sla error
C. debug ip routing
D. debug ip packet
Question 4 in IP SLA questions on right side list.
can anybody confirm the answer
Refer to the exhibit. An IP SLA was configured on router R1 that allows the default route to be modified in the event that Fa0/0 losses reachability with the router R3 Fa0/0 interface. The route has changed to flow through route R2.
Which debug command is used to troubleshoot this issue?
IP_SLA_Debug.jpg
A. debug ip flow
B. debug ip sla error
C. debug ip routing
D. debug ip packet