Share your ENARSI Experience

@anthcal do you remember what you chose for this one?

An administrator that is connected to the console does not see debug messages when remote users log in. Which action ensures that debug messages are displayed for remote loggings?

A. Enter the transport input ssh configuration command
B. Enter the terminal monitor exec command
C. Enter the logging console debugging configuration command
D. Enter the aaa new-model configuration command

@heyo you’re welcome man, good luck!

@twas that one should be “C. Enter the logging console debugging configuration command”

Since 14 August 2020, I already confirmed and informed you all that I passed exam and only studied Networktut May questions and 20 new questions but you all are crazy with H2P at that time. Hehehe.

Just Passed exam today, score 9XX all question from networktut premium but i think several answer from nework tut are wrong.

Hi

Could someone share link for new dump here?

what is the answer here ??

Refer to the exhibit. What is the result if applying this configuration?
R1#show policy-map control-plane
Control Plane
Service-policy input: CoPP-BGP
Class-map: BGP (match-all)
2716 packets, 193843 bytes
5 minute offered rate 0000 bps, drop rate 0000 bps
Match: access-group name BGP
drop
Class-map: class-default (match-any)
5212 packets, 64484847 bytes
5 minute offered rate 0000 bps, drop rate 0000 bps
Match: any
A. The router can form BGP neighborships with any other device. B. The router can form BGP neighborships with any device that matched by the access list named ―BGP‖ C. The router cannot form BGP neighborships with any other device D. The router cannot form BGP neighborships with any device that is matched by the access list named ―BGP‖

also here ?

Which command allows traffic to load-balance in an MPLS Layer 3 VPN configuration?
A. Multi-paths eibgp 2 B. Maximum-paths ibgp 2 C. Multi-paths 2 D. Maximum-paths 2

Refer to the exhibit An engineer is troubleshooting BGP on a device but discovers that the clock on the device does not correspond to the time stamp of the log entries. Which action ensures consistency between the two times?
*Feb 28 12:41:57: %BGP-5-ADJCHANGE: neighbor 192.168.2.2 Down User reset *Feb 28 12:41:57: %BGP_SESSION-5-ADJCHANGE : neighbor 192.168.2.2 IPv4 Unicast topology base removed from session User reset *Feb 28 12:41:57: %BGP-5-ADJCHANGE: neighbor 192.168.2.2 Up R1#show clock *13:42:00.506 CET Feb 28 2019
A. Configure the logging clock synchronize command in global configuration mode B. Configure the service timestamps log uptime command in global configuration mode C. Configure the service timestamps log datetime localtime command in global configuration mode D. Make sure that the clock on the device is synchronized with an NTP server

2.Refer to the exhibit. An engineer is trying to block the route to 192.168.2.2 from the routing table by using the configuration that is shown. The route is still present in the routing table as an OSPF route. Which action blocks the route?
Router#show access-lists
Standard IP access list 1
10 permit 192.168.2.2 (1 match)
Router#
Router#show route-map
route-map RM-OSPF-DL, permit, sequence 10
Match clauses:
ip address (access-lists): 1
Set clauses:
Policy routing matches: 0 packets, 0 bytes
Router#
Router#show running-config | section ospf
router ospf 1
network 192.168.1.1 0.0.0.0 area 0
network 192.168.12.0 0.0.0.255 area 0
distribute-list route-map RM-OSPF-DL in
Router#
A. Add this statement to the route map ―route-map RM-OSPF-DL deny 20‖ B. Use a prefix list instead of an access list in the route map C. Change sequence 10 in the route-map command from permit to deny D. Use an extended access list instead of a standard access list

3.
A. The flow exporter is configured but is not used. B. The flow monitor is applied in the wrong direction. C. The flow monitor is applied to the wrong interface. D. The destination of the flow exporter is not reachable.

4.Refer to the exhibit. Network operations cannot read or write an configuration on the device
with this configuration from the operation subnet. Which two configuration fix the issue? (Choose two)
snmp-server community ciscotest 1 snmp-server host 192.168.1.128 ciscotest snmp-server enable traps bgp
A. Configure SNMP rw permission in addition to community ciscotest B. Modify access list 1 and allow operations subnet in the access list C. Modify SNMP rw permission in addition to version 1 D. Configure SNMP rw permission in addition to version 1 E. Configure SNMP rw permission in addition to community ciscotest 1

Please assist
regards

@MTN
1st – D
2nd – C
3rd – C
4th – A
5th – A+B (not 100% sure)

@ AnthCal Thanks for showing up.

Who else can confirm the above answers.
I think Joly can also help us .

@MTN
@Anthcal
and what about this question

what is the answer here ??

Refer to the exhibit. What is the result if applying this configuration?
R1#show policy-map control-plane
Control Plane
Service-policy input: CoPP-BGP
Class-map: BGP (match-all)
2716 packets, 193843 bytes
5 minute offered rate 0000 bps, drop rate 0000 bps
Match: access-group name BGP
drop
Class-map: class-default (match-any)
5212 packets, 64484847 bytes
5 minute offered rate 0000 bps, drop rate 0000 bps
Match: any
A. The router can form BGP neighborships with any other device. B. The router can form BGP neighborships with any device that matched by the access list named ―BGP‖ C. The router cannot form BGP neighborships with any other device D. The router cannot form BGP neighborships with any device that is matched by the access list named ―BGP

@AnthCal Thanks a lot.

but I’m a little bit confused on the below, because according to Network TUT the answer is { D}
and you say its {C}

Which command allows traffic to load-balance in an MPLS Layer 3 VPN configuration?
A. Multi-paths eibgp 2 B. Maximum-paths ibgp 2 C. Multi-paths 2 D. Maximum-paths 2

Good day once again.
some one posted one latest question about VRF lite capability I cannot see it any more
please post it again .

regards.

Which configuration adds an IPv4 interface to an OSPFv3 process in OSPFv3 address family configuration?
A. Router# ospf3 1 address-family ipv4 B. Router(config-router)#ospfv3 1 ipv4 area 0 C. Router(config-router)#ospfv3 3 1 D. Router# ospfv3 1 address-family ipv4 unicast

??

@MTN That one should be B. Maximum-paths ibgp 2

@DD B. Router(config-router)#ospfv3 1 ipv4 area 0
Though in the exam it appears as interface configuration mode

Passed the test yesterday with 9xx. These dumps are 100% good enough and you dont need any other ones. I honestly didnt have a single question that wasnt on this site. Some of the answers I think are wrong as others have pointed out but you could probably still blindly follow those answers and still pass in the 800 range.

@heyo Congrats man!!! did you only use 9tut?

@heisenberg Yeah man you dont need anything else. You could literally not have read one thing about the materials and still pass the test in my opinion. I know some people on here have said you need H 2 P but thats not true at all.

@heisenberg When I say you dont have to read one thing about the materials, I should be more clear and say you dont need to even open a book as the only thing you need are the questions from here. Im not saying you should do this because the knowledge from these tests are important too, but if you just need to pass for a job or something, this site is enough.

@heyo I appreciate you feedback man. That is the answer I was looking for. Most of the time what you study in books, your practical knowledge all become useless when you sit for the exam, thats why we need to pass the cert at any cost then we will have time to build labs and study according to the company needs.

Good day.

let mi ask. Is it possible to get 100% in cisco exams
or has any one got 100% in the history ?

@MTN i have 1000 score when i take CCNA. So it is possible you getb1000 score in cisco exam

@heyo
Congrats man! I agree, it’s important to at least understand all of the topics that are in the exam, but yeah, you could go with just the Qs here and it will be fine.

Refer to the exhibit. A router receiving BGP routing updates from multiple neighbors for
routers in AS 690. What is the reason that the router still sends traffic that is destined to AS 690
to a neighbor other than 10.222.10.1?

A. The local preference value in another neighbor statement is higher than 250
B. The local preference value should be set to the same value as the weight in the route map
C. The route map is applied in the wrong direction
D. The weight value in another statement is higher than 200

Can someone confirm answer for this question

Good day class mate

To all those who are interested in JUNIPER NETWORKS.
they are offering free exams for all their associate levels until 15 October.

for more information login to their site

TUT’s dumps are the best. ;)

any passing today ?! need a feedback pls

Passed few minutes ago, networks tut’s questions are valid. No question outside these dumps

can you say your score or approximate value please?

Hi Guys, Please let me know correct answer for this question. Thanks in advance.

An administrator that is connected to the console does not see debug messages when remote users log in.

Which action ensures that debug messages are displayed for remote loggings?
A . Enter the transport input ssh configuration command.
B . Enter the terminal monitor exec command.
C . Enter the logging console debugging configuration command.
D . Enter the aaa new-model configuration command.

B or C ?